ALPHA6460V series special AC drive is exclusively used in cross cutter. In packing and processing industries, there is the cut-to-length process on materials in constant conveying. Conventional cross cut machine consists of PLC and servo system. Cross cut, also known asrotary cut or flying saw, is one of the cut-to-length methods. It allows the material to be vertically cut along its conveying direction. In both packaging and processing industries, the constantly running materials must undergo the cut-to-length process.
ALPHA6460V series realizes the cross cutting by controlling the commonasynchronous motor.It can work in rotary-cut, flying shear, and flying-saw with low system cost, good control performance, wide application,flexible process adjustment, and convenient operation, ALPHA6460V series provides a brand new drive and control solution to cross cutting industry.
兴发老虎机Cutting precision: ±3mmat speed of 120m/s
Smooth speed curve: Generate motion track by using high precision electric cam; the speed and Acc. curves varying smoothly
兴发老虎机Valid for rotary-cutting, after-cutting and flying cutting
Ten groups of cutting length switchable and can be set during running
Manual & Auto cutting modes
Valid for multi-cutter system; Faster cutting
Valid for color-mark correction; applied in the cutting of compensated printing/ position bias on paper or package bags
Material feeding simulation; easy for testing anddebugging
The special AC drive for cross cutter can be often found in the corrugated paper cutting machine, packaging machinery, color printing presses, flying saws, rolling mills, punching machines, embossing machines, slitters, filling machines, and the high-speed wire and rebar cutting machines, among others.
Technical Specifications of ALPHA6460V
|Power Range||380V ±20% three phases: From 1.5 to 93kW|
|Rated Input Voltage and Frequency||380V three phases: 50/60Hz|
|Allowable Input Voltage Range||380V three phases: from 304 to 456V, Voltage unbalance rate of less than 3%, Frequency fluctuation of below ±5%?|
|Rated Output Voltage||From 0 to rated input voltage|
|Max. Overload Current||G model: 150% for one minute, 180% for 20 seconds|
|Control Method||V/F control, Open loop vector control, Close loop vector control|
|Frequency Range||From 0.00 to 650.00Hz (from 3R75GB to 3004GB)
From 0.00 to 400.00Hz (from 35R5GB to 3500G)
|Frequency Accuracy||Digital command ± 0.01% (from -10℃ to +40℃)
Simulation command ± 0.01% (25℃ ± 10℃)
|Preset Frequency Resolution||Digital command 0.01Hz
Simulation command 1/1000 of the maximum frequency
|Output Frequency Resolution||0.01Hz|
|Preset Frequency Signal||From 0 to 10V, from 0 to 20mA|
|Acceleration-Deceleration Time||From 0.1 to 3600 seconds (The acceleration and deceleration time are set individually.)|
|Braking Torque||The additional braking resistance reaches up to 125%.|
|Voltage-Frequency Characteristic||Four kinds of fixed V/F characteristics are selectable.
Any V/F characteristic can be preset.
The V/F control with PG is available.
|Protective Functions||Over-voltage, under-voltage, current limit, over-current, overload, electronic thermal relay, overheating, over-voltage stall, load short circuit, grounding, under-voltage protection, input phase loss, output phase loss, short circuit to ground, interphase short circuit, motor overload protection, etc|
|Ambient Temperature||From -10℃ to +40℃|
|Humidity||From 5 to 95% RH (No condensation)|
|Storage Temperature||From -40℃ to +70℃|
|Service Place||Indoor (without any corrosive gas)|
|Installation Site||The altitude is at most 1,000m. There is not any dust, corrosive gas, or direct solar radiation.|
|Vibration||Less than 5.9m/s2 (0.6g)|
|Cooling Method||Natural cooling or forced air cooling|
ALPHA6460V Selection Table
|Voltage Classes||Model||Motor Power (kW)||Rated Output Current (A)|
|380V Three Phases||6460V-3R75GB||0.75||2.5|
Overall Dimension of ALPHA6460V Series Special AC Drive for Cross Cutter
Frequency Inverter | Drive And Control Solution | Crosscut Control System